Bestsellers
- -10%
blade for slicer 250 diameter 25cm three hole central hole 40mm c45 rgv fac e
"
BLADE FOR SLICER 250 DIAMETER 25CM THREE HOLE CENTRAL HOLE 40MM C45 RGV FAC E
| (E) Diameter Blade | 250 | |
| (V) Number of holes | 3 | |
| (F) Dim. Central hole | 40 | |
| (H) Blade height (thickness) | 17.5 | |
| (I) Inner blade measurement (blade guard) | 210 |
VISIT THE BLOG FOR MORE INFORMATION
"
- -10%
neutral white oil pack for slicers 50 ml
Food-grade neutral white oil, 50 ml, for lubricating gravity-feed and flywheel slicers of any brand: colourless, odourless and tasteless, it protects the carriage, food pusher and blade from friction and rust. Do not use cooking oils.
- -10%
blade for slicer 220 diameter 22cm three hole central hole 40mm c45 rgv and other brands
BLADE FOR SLICER? 220/40/3/180 / 15,5 C45 FOR ABO - KOLOSSAL - OMAS -VAN DALL
(E) Diameter Blade 220
(V) Hole Number 3
(F) Dim. Central Hole 40
(H) Blade height (thickness) 15.5
(I) Internal blade size (cap) 180
VISIT THE BLOG FOR MORE INFORMATION
hand protection slicer fac and swedlinghaus model 195 220 250r 250e
Carriage hand guard for FAC and Swedlinghaus gravity-feed slicers, models 195 / 220 / 250R / 250E, CE and CE domestic versions. Safety shield between the hand and the blade during slicing: mandatory component, to be replaced if broken or missing. Hole centre distance 14.9 cm (measurement to check for compatibility). Specific to FAC/Swedlinghaus, not interchangeable with RGV models.
45x7x10 emery for mobba slicer and compatible fine grain
The emery is the abrasive stone fitted to the built-in sharpener of the slicer: as it spins against the blade's edge, it restores its cutting ability. Sharpening typically uses two stones, a coarse-grit one for the initial grinding pass and a fine-grit one like this for the finishing pass, which follows the coarse stage and leaves the edge clean, thin and even — ideal for slicing without tearing or overheating the food.
- Emery diameter: 45 mm
- Thickness: 7 mm
- Centre hole: 10 mm
- Grit: fine
Compatible with Mobba slicers and compatible models (ref. 410MBFC10). Replace it when the abrasive surface looks worn, glazed or smoothed out: at that point it no longer 'bites' into the metal and sharpening becomes ineffective, leaving the edge dull instead of sharp and forcing extra passes to get the same result.
Data sheet
- DIAMETRO SMERIGLIO
- 45
- FORO CENTRALE SMERIGLIO
- 10
- SPESSORE SMERIGLIO
- 7
Specific References
- MPN
- AGWS-255
Customers who bought this product also bought:
graduated knob with pin diameter 14mm length 80mm white bezel
Graduated "clock-style" knob for slicer thickness adjustment: pin diameter 14 mm, length 80 mm, white bezel. Match to regulators with identical pin dimensions.
- -10%
30cm blade for flywheel slicer diameter 300 thickness 18.5 hole 25.4 flat adaptable berkel
Replacement blade for flywheel slicers (Berkel-type), Ø300 mm, center hole 25.4 mm, thickness 18.5 mm, 1 hole, C45 carbon steel. Compatible with Berkel and Lamda flywheel models. C45 holds its edge well but is not stainless: keep it sharp and protected with a light film of food-grade oil. Check diameter, hole and thickness against the blade currently fitted before purchasing.